ipmimonitoring.conf.5 - Online Linux Manual Page

FREEIPMI_INTERPRET_SENSOR - Online Linux Manual PageSection : 5
Updated : 2017-03-22
Source : FreeIPMI 1.2.1
Note : Configuration

NAMEfreeipmi_interpret_sensor.conf − specify sensor interpretation rules

DESCRIPTIONThe /etc//freeipmi_interpret_sensor.conf defines how IPMI sensors should be interpreted. IPMI based sensors specify a number of states/thresholds when they are read. Based on those states/thresholds, libraries and tools such as libfreeipmi(3), libipmimonitoring(3) and ipmi-sensors(8) can report if a sensor reading is "good" or "bad" via a report of a NOMINAL, WARNING, or CRITICAL state. Each of the states listed below are (hopefully) descriptive enough to describe the state conditions that may be set/unset for each sensor type. For more detailed information on each of the individual states listed below, please see the IPMI Specification "Sensor and Event Code Tables". Ipmi-sensors(8) can be used to determine the sensor types and the states/thresholds that exist on a system by outputting very verbose output and seeing what types of Assertion or Deassertion events are possible. The possible values for all states/thresholds below are: Nominal - Signal Nominal reading if state/threshold tripped Warning - Signal Warning reading if state/treshold tripped Critical - Signal Critical reading if state/threshold tripped Not all IPMI sensor types and event types are currently supported. If you would like more to be supported, please e-mail the FreeIPMI mailing list. The default values selected for individual states/thresholds being tripped are based on best guesses and motherboards being analyzed. If you think they should be changed, please e-mail the FreeIPMI mailing list to discuss what the defaults should be. Most default interpretations can be determined quite easily and can meet the needs of most users. For example, a reading of "Performance_Met" is normally better than "Performance_Lags". However, some sensors can be ambiguous and depend completely on the manufacturer. For example, "State_Asserted" vs. "State_Deasserted" are completely at the interpretation of the vendor. Users are advised to adjust the interpretations below as needed for their machines. Every group of state conditions below includes a configuration for "No_Event". This is the condition under which no sensor states/events have occurred or are triggered. Under most conditions, a mapping to "Nominal" is preferred. However, under some circumstances, it may be useful to report something else. For example, if a sensor on a particular motherboard is required to report a state/event, a no sensor state condition could indicate a broken a sensor. This is highly dependent on the motherboard.

FORMATThe configuration options that can be specified in the configuration file are listed below. Each configuration option must be listed on a separate line. Arguments for an option are separated by any amount of whitespace. Multiple arguments are also separated by whitespace. Comments can be marked by using the pound sign ("#") character, and lines can be continued on the next using backslash ("\").

OPTIONSIPMI_Threshold_Sensor The following states correspond to threshold sensors. This normally applies to sensors that measure non-discrete values, such as temperatures, voltages, RPM, etc. IPMI_Threshold_Sensor_No_Event Defaults to Nominal. IPMI_Threshold_Sensor_At_Or_Below_Lower_Non_Critical_Threshold Defaults to Nominal. IPMI_Threshold_Sensor_At_Or_Below_Lower_Critical_Threshold Defaults to Critical. IPMI_Threshold_Sensor_At_Or_Below_Lower_Non_Recoverable_Threshold Defaults to Critical. IPMI_Threshold_Sensor_At_Or_Above_Upper_Non_Critical_Threshold Defaults to Nominal. IPMI_Threshold_Sensor_At_Or_Above_Upper_Critical_Threshold Defaults to Critical. IPMI_Threshold_Sensor_At_Or_Above_Upper_Non_Recoverable_Threshold Defaults to Critical. IPMI_Temperature_State The following states correspond to Temperature sensors that report an assertion or deassertion. IPMI_Temperature_State_No_Event Defaults to Nominal. IPMI_Temperature_State_Deasserted Defaults to Nominal. IPMI_Temperature_State_Asserted Defaults to Warning. IPMI_Temperature_Limit The following states correspond to Temperature sensors that report on limits. IPMI_Temperature_Limit_No_Event Defaults to Nominal. IPMI_Temperature_Limit_Not_Exceeded Defaults to Nominal. IPMI_Temperature_Limit_Exceeded Defaults to Critical. IPMI_Temperature_Transition_Severity The following states correspond to Temperature sensors that report on device severity. IPMI_Temperature_Transition_Severity_No_Event Defaults to Nominal. IPMI_Temperature_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Temperature_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Temperature_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Temperature_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Temperature_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Temperature_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Temperature_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Temperature_Transition_Severity_Monitor Defaults to Warning. IPMI_Temperature_Transition_Severity_Informational Defaults to Nominal. IPMI_Voltage_State The following states correspond to Voltage sensors that report an assertion or deassertion. IPMI_Voltage_State_No_Event Defaults to Nominal. IPMI_Voltage_State_Deasserted Defaults to Nominal. IPMI_Voltage_State_Asserted Defaults to Warning. IPMI_Voltage_Limit The following states correspond to Voltage sensors that report on limits. IPMI_Voltage_Limit_No_Event Defaults to Nominal. IPMI_Voltage_Limit_Not_Exceeded Defaults to Nominal. IPMI_Voltage_Limit_Exceeded Defaults to Critical. IPMI_Voltage_Performance The following states correspond to Voltage sensors that report on performance. IPMI_Voltage_Performance_No_Event Defaults to Nominal. IPMI_Voltage_Performance_Met Defaults to Nominal. IPMI_Voltage_Performance_Lags Defaults to Critical. IPMI_Voltage_Transition_Severity The following states correspond to Voltage sensors that report on device severity. IPMI_Voltage_Transition_Severity_No_Event Defaults to Nominal. IPMI_Voltage_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Voltage_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Voltage_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Voltage_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Voltage_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Voltage_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Voltage_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Voltage_Transition_Severity_Monitor Defaults to Warning. IPMI_Voltage_Transition_Severity_Informational Defaults to Nominal. IPMI_Current_Transition_Severity The following states correspond to Current sensors that report on device severity. IPMI_Current_Transition_Severity_No_Event Defaults to Nominal. IPMI_Current_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Current_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Current_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Current_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Current_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Current_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Current_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Current_Transition_Severity_Monitor Defaults to Warning. IPMI_Current_Transition_Severity_Informational Defaults to Nominal. IPMI_Fan_State The following states correspond to Fan sensors that report an assertion or deassertion. IPMI_Fan_State_No_Event Defaults to Nominal. IPMI_Fan_State_Deasserted Defaults to Nominal. IPMI_Fan_State_Asserted Defaults to Warning. IPMI_Fan_Transition_Severity The following states correspond to Fan sensors that report on device severity. IPMI_Fan_Transition_Severity_No_Event Defaults to Nominal. IPMI_Fan_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Fan_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Fan_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Fan_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Fan_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Fan_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Fan_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Fan_Transition_Severity_Monitor Defaults to Warning. IPMI_Fan_Transition_Severity_Informational Defaults to Nominal. IPMI_Fan_Device_Present The following states correspond to Fan sensors that report on device installation. IPMI_Fan_Device_Present_Device_No_Event Defaults to Nominal. IPMI_Fan_Device_Present_Device_Removed_Device_Absent Defaults to Critical. IPMI_Fan_Device_Present_Device_Inserted_Device_Present Defaults to Nominal. IPMI_Power_Supply_Transition_Severity The following states correspond to Power Supply sensors that report on device severity. IPMI_Power_Supply_Transition_Severity_No_Event Defaults to Nominal. IPMI_Power_Supply_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Power_Supply_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Power_Supply_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Power_Supply_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Power_Supply_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Power_Supply_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Power_Supply_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Power_Supply_Transition_Severity_Monitor Defaults to Warning. IPMI_Power_Supply_Transition_Severity_Informational Defaults to Nominal. IPMI_Fan_Transition_Availability The following states correspond to Fan sensors that report on device availability. IPMI_Fan_Transition_Availability_No_Event Defaults to Nominal. IPMI_Fan_Transition_Availability_To_Running Defaults to Nominal. IPMI_Fan_Transition_Availability_To_In_Test Defaults to Warning. IPMI_Fan_Transition_Availability_To_Power_Off Defaults to Warning. IPMI_Fan_Transition_Availability_To_On_Line Defaults to Warning. IPMI_Fan_Transition_Availability_To_Off_Line Defaults to Warning. IPMI_Fan_Transition_Availability_To_Off_Duty Defaults to Warning. IPMI_Fan_Transition_Availability_To_Degraded Defaults to Critical. IPMI_Fan_Transition_Availability_To_Power_Save Defaults to Warning. IPMI_Fan_Transition_Availability_Install_Error Defaults to Critical. IPMI_Fan_Redundancy The following states correspond to Fan sensors that report on redundancy. IPMI_Fan_Redundancy_No_Event Defaults to Nominal. IPMI_Fan_Redundancy_Fully_Redundant Defaults to Nominal. IPMI_Fan_Redundancy_Redundancy_Lost Defaults to Critical. IPMI_Fan_Redundancy_Redundancy_Degraded Defaults to Warning. IPMI_Fan_Redundancy_Non_Redundant_Sufficient_Resources_From_Redundant Defaults to Critical. IPMI_Fan_Redundancy_Non_Redundant_Sufficient_Resources_From_Insufficient_Redundancy Defaults to Critical. IPMI_Fan_Redundancy_Non_Redundant_Insufficient_Resources Defaults to Critical. IPMI_Fan_Redundancy_Redundancy_Degraded_From_Fully_Redundant Defaults to Warning. IPMI_Fan_Redundancy_Redundancy_Degraded_From_Non_Redundant Defaults to Warning. IPMI_Physical_Security The following states correspond to Physical Security sensors w/ Physical Security specific output states. IPMI_Physical_Security_No_Event Defaults to Nominal. IPMI_Physical_Security_General_Chassis_Intrusion Defaults to Critical. IPMI_Physical_Security_Drive_Bay_Intrusion Defaults to Critical. IPMI_Physical_Security_IO_Card_Intrusion Defaults to Critical. IPMI_Physical_Security_Processor_Area_Intrusion Defaults to Critical. IPMI_Physical_Security_LAN_Leash_Lost Defaults to Critical. IPMI_Physical_Security_Unauthorized_Dock_Undock Defaults to Critical. IPMI_Physical_Security_FAN_Area_Intrusion Defaults to Critical. IPMI_Platform_Security_Violation_Attempt The following states correspond to Platform Violation Attempt sensors w/ Platform Security Violation Attempt specific output states. IPMI_Platform_Security_Violation_Attempt_No_Event Defaults to Nominal. IPMI_Platform_Security_Violation_Attempt_Secure_Mode_Violation_Attempt Defaults to Critical. IPMI_Platform_Security_Violation_Attempt_Pre_Boot_Password_Violation_User_Password Defaults to Critical. IPMI_Platform_Security_Violation_Attempt_Pre_Boot_Password_Violation_Attempt_Setup_Password Defaults to Critical. IPMI_Platform_Security_Violation_Attempt_Pre_Boot_Password_Violation_Network_Boot_Password Defaults to Critical. IPMI_Platform_Security_Violation_Attempt_Other_Pre_Boot_Password_Violation Defaults to Critical. IPMI_Platform_Security_Violation_Attempt_Out_Of_Band_Access_Password_Violation Defaults to Critical. IPMI_Processor The following states correspond to Processor sensors w/ Processor specific output states. IPMI_Processor_No_Event Defaults to Nominal. IPMI_Processor_IERR Defaults to Critical. IPMI_Processor_Thermal_Trip Defaults to Critical. IPMI_Processor_FRB1_BIST_Failure Defaults to Critical. IPMI_Processor_FRB2_Hang_In_POST_Failure Defaults to Critical. IPMI_Processor_FRB3_Processor_Startup_Initialization_Failure Defaults to Critical. IPMI_Processor_Configuration_Error Defaults to Critical. IPMI_Processor_SMBIOS_Uncorrectable_CPU_Complex_Error Defaults to Critical. IPMI_Processor_Processor_Presence_Detected Defaults to Nominal. IPMI_Processor_Processor_Disabled Defaults to Critical. IPMI_Processor_Terminator_Presence_Detected Defaults to Critical. IPMI_Processor_Processor_Automatically_Throttled Defaults to Warning. IPMI_Processor_Machine_Check_Exception Defaults to Critical. IPMI_Processor_Correctable_Machine_Check_Error Defaults to Warning. IPMI_Processor_State The following states correspond to Processor sensors that report an assertion or deassertion. IPMI_Processor_State_No_Event Defaults to Nominal. IPMI_Processor_State_Deasserted Defaults to Nominal. IPMI_Processor_State_Asserted Defaults to Critical. IPMI_Power_Supply The following states correspond to Power Supply sensors w/ Power Supply specific output states. IPMI_Power_Supply_No_Event Defaults to Nominal. IPMI_Power_Supply_Presence_Detected Defaults to Nominal. IPMI_Power_Supply_Power_Supply_Failure_Detected Defaults to Critical. IPMI_Power_Supply_Predictive_Failure Defaults to Critical. IPMI_Power_Supply_Power_Supply_Input_Lost_AC_DC Defaults to Critical. IPMI_Power_Supply_Power_Supply_Input_Lost_Or_Out_Of_Range Defaults to Critical. IPMI_Power_Supply_Power_Supply_Input_Out_Of_Range_But_Present Defaults to Critical. IPMI_Power_Supply_Configuration_Error Defaults to Critical. IPMI_Power_Supply_State The following states correspond to Power_Supply sensors that report an assertion or deassertion. IPMI_Power_Supply_State_No_Event Defaults to Nominal. IPMI_Power_Supply_State_Deasserted Defaults to Critical. IPMI_Power_Supply_State_Asserted Defaults to Nominal. IPMI_Power_Supply_Redundancy The following states correspond to Power Supply sensors that report on redundancy. IPMI_Power_Supply_Redundancy_No_Event Defaults to Nominal. IPMI_Power_Supply_Redundancy_Fully_Redundant Defaults to Nominal. IPMI_Power_Supply_Redundancy_Redundancy_Lost Defaults to Critical. IPMI_Power_Supply_Redundancy_Redundancy_Degraded Defaults to Warning. IPMI_Power_Supply_Redundancy_Non_Redundant_Sufficient_Resources_From_Redundant Defaults to Critical. IPMI_Power_Supply_Redundancy_Non_Redundant_Sufficient_Resources_From_Insufficient_Redundancy Defaults to Critical. IPMI_Power_Supply_Redundancy_Non_Redundant_Insufficient_Resources Defaults to Critical. IPMI_Power_Supply_Redundancy_Redundancy_Degraded_From_Fully_Redundant Defaults to Warning. IPMI_Power_Supply_Redundancy_Redundancy_Degraded_From_Non_Redundant Defaults to Warning. IPMI_Power_Unit The following states correspond to Power Unit sensors w/ Power Unit specific output states. IPMI_Power_Unit_No_Event Defaults to Nominal. IPMI_Power_Unit_Power_Off_Power_Down Defaults to Nominal. IPMI_Power_Unit_Power_Cycle Defaults to Nominal. IPMI_Power_Unit_240VA_Power_Down Defaults to Warning. IPMI_Power_Unit_Interlock_Power_Down Defaults to Warning. IPMI_Power_Unit_AC_Lost Defaults to Critical. IPMI_Power_Unit_Soft_Power_Control_Failure Defaults to Critical. IPMI_Power_Unit_Power_Unit_Failure_Detected Defaults to Critical. IPMI_Power_Unit_Predictive_Failure Defaults to Critical. IPMI_Power_Unit_Device_Present The following states correspond to Power Unit sensors that report on device installation. IPMI_Power_Unit_Device_Present_No_Event Defaults to Nominal. IPMI_Power_Unit_Device_Present_Device_Removed_Device_Absent Defaults to Critical. IPMI_Power_Unit_Device_Present_Device_Inserted_Device_Present Defaults to Nominal. IPMI_Power_Unit_Redundancy The following states correspond to Power Unit sensors that report on redundancy. IPMI_Power_Unit_Redundancy_No_Event Defaults to Nominal. IPMI_Power_Unit_Redundancy_Fully_Redundant Defaults to Nominal. IPMI_Power_Unit_Redundancy_Redundancy_Lost Defaults to Critical. IPMI_Power_Unit_Redundancy_Redundancy_Degraded Defaults to Warning. IPMI_Power_Unit_Redundancy_Non_Redundant_Sufficient_Resources_From_Redundant Defaults to Critical. IPMI_Power_Unit_Redundancy_Non_Redundant_Sufficient_Resources_From_Insufficient_Redundancy Defaults to Critical. IPMI_Power_Unit_Redundancy_Non_Redundant_Insufficient_Resources Defaults to Critical. IPMI_Power_Unit_Redundancy_Redundancy_Degraded_From_Fully_Redundant Defaults to Warning. IPMI_Power_Unit_Redundancy_Redundancy_Degraded_From_Non_Redundant Defaults to Warning. IPMI_Cooling_Device_Redundancy The following states correspond to Cooling Device sensors that report on redundancy. IPMI_Cooling_Device_Redundancy_No_Event Defaults to Nominal. IPMI_Cooling_Device_Redundancy_Fully_Redundant Defaults to Nominal. IPMI_Cooling_Device_Redundancy_Redundancy_Lost Defaults to Critical. IPMI_Cooling_Device_Redundancy_Redundancy_Degraded Defaults to Warning. IPMI_Cooling_Device_Redundancy_Non_Redundant_Sufficient_Resources_From_Redundant Defaults to Critical. IPMI_Cooling_Device_Redundancy_Non_Redundant_Sufficient_Resources_From_Insufficient_Redundancy Defaults to Critical. IPMI_Cooling_Device_Redundancy_Non_Redundant_Insufficient_Resources Defaults to Critical. IPMI_Cooling_Device_Redundancy_Redundancy_Degraded_From_Fully_Redundant Defaults to Warning. IPMI_Cooling_Device_Redundancy_Redundancy_Degraded_From_Non_Redundant Defaults to Warning. IPMI_Memory The following states correspond to Memory sensors w/ Memory specific output states. IPMI_Memory_No_Event Defaults to Nominal. IPMI_Memory_Correctable_Memory_Error Defaults to Warning. IPMI_Memory_Uncorrectable_Memory_Error Defaults to Critical. IPMI_Memory_Parity Defaults to Critical. IPMI_Memory_Memory_Scrub_Failed Defaults to Critical. IPMI_Memory_Memory_Device_Disabled Defaults to Critical. IPMI_Memory_Correctable_Memory_Error_Logging_Limit_Reached Defaults to Warning. IPMI_Memory_Presence_Detected Defaults to Nominal. IPMI_Memory_Configuration_Error Defaults to Critical. IPMI_Memory_Spare Defaults to Nominal. IPMI_Memory_Memory_Automatically_Throttled Defaults to Warning. IPMI_Memory_Critical_Overtemperature Defaults to Critical. IPMI_Memory_State The following states correspond to Memory sensors that report an assertion or deassertion. IPMI_Memory_State_No_Event Defaults to Nominal. IPMI_Memory_State_Deasserted Defaults to Nominal. IPMI_Memory_State_Asserted Defaults to Critical. IPMI_Memory_Transition_Severity The following states correspond to Memory sensors that report on device severity. IPMI_Memory_Transition_Severity_No_Event Defaults to Nominal. IPMI_Memory_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Memory_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Memory_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Memory_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Memory_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Memory_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Memory_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Memory_Transition_Severity_Monitor Defaults to Warning. IPMI_Memory_Transition_Severity_Informational Defaults to Nominal. IPMI_Memory_Redundancy The following states correspond to Cooling Device sensors that report on redundancy. IPMI_Memory_Redundancy_No_Event Defaults to Nominal. IPMI_Memory_Redundancy_Fully_Redundant Defaults to Nominal. IPMI_Memory_Redundancy_Redundancy_Lost Defaults to Critical. IPMI_Memory_Redundancy_Redundancy_Degraded Defaults to Warning. IPMI_Memory_Redundancy_Non_Redundant_Sufficient_Resources_From_Redundant Defaults to Critical. IPMI_Memory_Redundancy_Non_Redundant_Sufficient_Resources_From_Insufficient_Redundancy Defaults to Critical. IPMI_Memory_Redundancy_Non_Redundant_Insufficient_Resources Defaults to Critical. IPMI_Memory_Redundancy_Redundancy_Degraded_From_Fully_Redundant Defaults to Warning. IPMI_Memory_Redundancy_Redundancy_Degraded_From_Non_Redundant Defaults to Warning. IPMI_Drive_Slot The following states correspond to Drive Slot sensors w/ Drive Slot specific output states. IPMI_Drive_Slot_No_Event Defaults to Nominal. IPMI_Drive_Slot_Drive_Presence Defaults to Nominal. IPMI_Drive_Slot_Drive_Fault Defaults to Critical. IPMI_Drive_Slot_Predictive_Failure Defaults to Critical. IPMI_Drive_Slot_Hot_Spare Defaults to Nominal. IPMI_Drive_Slot_Consistency_Check_Parity_Check_In_Progress Defaults to Nominal. IPMI_Drive_Slot_In_Critical_Array Defaults to Critical. IPMI_Drive_Slot_In_Failed_Array Defaults to Critical. IPMI_Drive_Slot_Rebuild_Remap_In_Progress Defaults to Nominal. IPMI_Drive_Slot_Rebuild_Remap_Aborted Defaults to Critical. IPMI_Drive_Slot_State The following states correspond to Drive Slot sensors that report an assertion or deassertion. IPMI_Drive_Slot_State_No_Event Defaults to Nominal. IPMI_Drive_Slot_State_Deasserted Defaults to Warning. IPMI_Drive_Slot_State_Asserted Defaults to Nominal. IPMI_Drive_Slot_Predictive_Failure The following states correspond to Drive_Slot sensors that report a predictive failure assertion or deassertion. IPMI_Drive_Slot_Predictive_Failure_No_Event Defaults to Nominal. IPMI_Drive_Slot_Predictive_Failure_Deasserted Defaults to Nominal. IPMI_Drive_Slot_Predictive_Failure_Asserted Defaults to Critical. IPMI_Drive_Slot_Device_Present The following states correspond to Drive Slot sensors that report on device installation. IPMI_Drive_Slot_Device_Present_No_Event Defaults to Nominal. IPMI_Drive_Slot_Device_Present_Device_Removed_Device_Absent Defaults to Critical. IPMI_Drive_Slot_Device_Present_Device_Inserted_Device_Present Defaults to Nominal. IPMI_POST_Memory_Resize_State The following states correspond to POST Memory Resize sensors that report an assertion or deassertion. IPMI_POST_Memory_Resize_State_No_Event Defaults to Nominal. IPMI_POST_Memory_Resize_State_Deasserted Defaults to Nominal. IPMI_POST_Memory_Resize_State_Asserted Defaults to Warning. IPMI_System_Firmware_Progress The following states correspond to System Firmware Progress sensors w/ System Firmware Progress specific output states. IPMI_System_Firmware_Progress_No_Event Defaults to Nominal. IPMI_System_Firmware_Progress_System_Firmware_Error Defaults to Critical. IPMI_System_Firmware_Progress_System_Firmware_Hang Defaults to Critical. IPMI_System_Firmware_Progress_System_Firmware_Progress Defaults to Nominal. IPMI_System_Firmware_Progress_Transition_Severity The following states correspond to System Firmware Progress sensors that report on device severity. IPMI_System_Firmware_Progress_Transition_Severity_No_Event Defaults to Nominal. IPMI_System_Firmware_Progress_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_System_Firmware_Progress_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_System_Firmware_Progress_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_System_Firmware_Progress_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_System_Firmware_Progress_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_System_Firmware_Progress_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_System_Firmware_Progress_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_System_Firmware_Progress_Transition_Severity_Monitor Defaults to Warning. IPMI_System_Firmware_Progress_Transition_Severity_Informational Defaults to Nominal. IPMI_Event_Logging_Disabled The following states correspond to Event Logging Disabled sensors w/ IPMI_Event_Logging_Disabled_No_Event Defaults to Nominal. IPMI_Event_Logging_Disabled_Correctable_Memory_Error_Logging_Disabled Defaults to Critical. IPMI_Event_Logging_Disabled_Event_Type_Logging_Disabled Defaults to Critical. IPMI_Event_Logging_Disabled_Log_Area_Reset_Cleared Defaults to Nominal. IPMI_Event_Logging_Disabled_All_Event_Logging_Disabled Defaults to Critical. IPMI_Event_Logging_Disabled_SEL_Full Defaults to Critical. IPMI_Event_Logging_Disabled_SEL_Almost_Full Defaults to Warning. IPMI_Event_Logging_Disabled_Correctable_Machine_Check_Error_Logging_Disabled Defaults to Critical. IPMI_System_Event The following states correspond to System Event sensors w/ System Event specific output states. IPMI_System_Event_No_Event Defaults to Nominal. IPMI_System_Event_System_Reconfigured Defaults to Warning. IPMI_System_Event_OEM_System_Boot_Event Defaults to Nominal. IPMI_System_Event_Undetermined_System_Hardware_Failure Defaults to Critical. IPMI_System_Event_Entry_Added_To_Auxiliary_Log Defaults to Nominal. IPMI_System_Event_PEF_Action Defaults to Nominal. IPMI_System_Event_Timestamp_Clock_Sync Defaults to Warning. IPMI_System_Event_Transition_State The following states correspond to System Event sensors that report a transition state. IPMI_System_Event_Transition_State_No_Event Defaults to Nominal. IPMI_System_Event_Transition_State_Active Defaults to Nominal. IPMI_System_Event_Transition_State_Idle Defaults to Nominal. IPMI_System_Event_Transition_State_Busy Defaults to Nominal. IPMI_System_Event_State The following states correspond to System Event sensors that report an assertion or deassertion. IPMI_System_Event_State_No_Event Defaults to Nominal. IPMI_System_Event_State_Deasserted Defaults to Nominal. IPMI_System_Event_State_Asserted Defaults to Warning. IPMI_Critical_Interrupt The following states correspond to Critical Interrupt sensors w/ Critical Interrupt specific output states. IPMI_Critical_Interrupt_No_Event Defaults to Nominal. IPMI_Critical_Interrupt_Front_Panel_NMI_Diagnostic_Interrupt Defaults to Critical. IPMI_Critical_Interrupt_Bus_Timeout Defaults to Critical. IPMI_Critical_Interrupt_IO_Channel_Check_NMI Defaults to Critical. IPMI_Critical_Interrupt_Software_NMI Defaults to Warning. IPMI_Critical_Interrupt_PCI_PERR Defaults to Critical. IPMI_Critical_Interrupt_PCI_SERR Defaults to Critical. IPMI_Critical_Interrupt_EISA_Fail_Safe_Timeout Defaults to Critical. IPMI_Critical_Interrupt_Bus_Correctable_Error Defaults to Warning. IPMI_Critical_Interrupt_Bus_Uncorrectable_Error Defaults to Critical. IPMI_Critical_Interrupt_Fatal_NMI Defaults to Critical. IPMI_Critical_Interrupt_Bus_Fatal_Error Defaults to Critical. IPMI_Critical_Interrupt_Bus_Degraded Defaults to Warning. IPMI_Button_Switch The following states correspond to Button/Switch sensors w/ Button/Switch specific output states. IPMI_Button_Switch_No_Event Defaults to Nominal. IPMI_Button_Switch_Power_Button_Pressed Defaults to Nominal. IPMI_Button_Switch_Sleep_Button_Pressed Defaults to Nominal. IPMI_Button_Switch_Reset_Button_Pressed Defaults to Nominal. IPMI_Button_Switch_FRU_Latch_Open Defaults to Warning. IPMI_Button_Switch_FRU_Service_Request_Button Defaults to Warning. IPMI_Button_Switch_State The following states correspond to Button/Switch sensors that report an assertion or deassertion. IPMI_Button_Switch_State_No_Event Defaults to Nominal. IPMI_Button_Switch_State_Deasserted Defaults to Nominal. IPMI_Button_Switch_State_Asserted Defaults to Nominal. IPMI_Button_Switch_Transition_Severity The following states correspond to Button/Switch sensors that report on device severity. IPMI_Button_Switch_Transition_Severity_No_Event Defaults to Nominal. IPMI_Button_Switch_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Button_Switch_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Button_Switch_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Button_Switch_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Button_Switch_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Button_Switch_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Button_Switch_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Button_Switch_Transition_Severity_Monitor Defaults to Warning. IPMI_Button_Switch_Transition_Severity_Informational Defaults to Nominal. IPMI_Module_Board_State The following states correspond to Module/Board sensors that report an assertion or deassertion. IPMI_Module_Board_State_No_Event Defaults to Nominal. IPMI_Module_Board_State_Deasserted Defaults to Nominal. IPMI_Module_Board_State_Asserted Defaults to Critical. IPMI_Module_Board_Device_Present The following states correspond to Module/Board sensors that report on device installation. IPMI_Module_Board_Device_Present_No_Event Defaults to Nominal. IPMI_Module_Board_Device_Present_Device_Removed_Device_Absent Defaults to Critical. IPMI_Module_Board_Device_Present_Device_Inserted_Device_Present Defaults to Nominal. IPMI_Chassis_Transition_Severity The following states correspond to Chassis sensors that report on device severity. IPMI_Chassis_Transition_Severity_No_Event Defaults to Nominal. IPMI_Chassis_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Chassis_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Chassis_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Chassis_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Chassis_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Chassis_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Chassis_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Chassis_Transition_Severity_Monitor Defaults to Warning. IPMI_Chassis_Transition_Severity_Informational Defaults to Nominal. IPMI_Chip_Set_Transition_Severity The following states correspond to Chip Set sensors that report on device severity. IPMI_Chip_Set_Transition_Severity_No_Event Defaults to Nominal. IPMI_Chip_Set_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Chip_Set_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Chip_Set_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Chip_Set_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Chip_Set_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Chip_Set_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Chip_Set_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Chip_Set_Transition_Severity_Monitor Defaults to Warning. IPMI_Chip_Set_Transition_Severity_Informational Defaults to Nominal. IPMI_Cable_Interconnect The following states correspond to Cable/Interconnect sensors w/ Cable/Interconnect specific output states. IPMI_Cable_Interconnect_No_Event Defaults to Nominal. IPMI_Cable_Interconnect_Is_Connected Defaults to Nominal. IPMI_Cable_Interconnect_Configuration_Error Defaults to Critical. IPMI_Cable_Interconnect_Transition_Severity The following states correspond to Cable/Interconnect sensors that report on device severity. IPMI_Cable_Interconnect_Transition_Severity_No_Event Defaults to Nominal. IPMI_Cable_Interconnect_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Cable_Interconnect_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Cable_Interconnect_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Cable_Interconnect_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Cable_Interconnect_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Cable_Interconnect_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Cable_Interconnect_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Cable_Interconnect_Transition_Severity_Monitor Defaults to Warning. IPMI_Cable_Interconnect_Transition_Severity_Informational Defaults to Nominal. IPMI_Boot_Error The following states correspond to Boot Error sensors w/ Boot Error specific output states. IPMI_Boot_Error_No_Event Defaults to Nominal. IPMI_Boot_Error_No_Bootable_Media Defaults to Critical. IPMI_Boot_Error_Non_Bootable_Diskette_Left_In_Drive Defaults to Critical. IPMI_Boot_Error_PXE_Server_Not_Found Defaults to Critical. IPMI_Boot_Error_Invalid_Boot_Sector Defaults to Critical. IPMI_Boot_Error_Timeout_Waiting_For_User_Selection_Of_Boot_Source Defaults to Warning. IPMI_Boot_Error_State The following states correspond to Boot Error sensors that report an assertion or deassertion. IPMI_Boot_Error_State_No_Event Defaults to Nominal. IPMI_Boot_Error_State_Deasserted Defaults to Nominal. IPMI_Boot_Error_State_Asserted Defaults to Critical. IPMI_Boot_Error_Transition_Severity The following states correspond to Boot Error sensors that report on device severity. IPMI_Boot_Error_Transition_Severity_No_Event Defaults to Nominal. IPMI_Boot_Error_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Boot_Error_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Boot_Error_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Boot_Error_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Boot_Error_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Boot_Error_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Boot_Error_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Boot_Error_Transition_Severity_Monitor Defaults to Warning. IPMI_Boot_Error_Transition_Severity_Informational Defaults to Nominal. IPMI_OS_Boot The following states correspond to OS Boot sensors w/ OS Boot specific output events. IPMI_OS_Boot_No_Event Defaults to Nominal. IPMI_OS_Boot_A_Boot_Completed Defaults to Nominal. IPMI_OS_Boot_C_Boot_Completed Defaults to Nominal. IPMI_OS_Boot_PXE_Boot_Completed Defaults to Nominal. IPMI_OS_Boot_Diagnostic_Boot_Completed Defaults to Nominal. IPMI_OS_Boot_CD_ROM_Boot_Completed Defaults to Nominal. IPMI_OS_Boot_ROM_Boot_Completed Defaults to Nominal. IPMI_OS_Boot_Boot_Completed_Boot_Device_Not_Specified Defaults to Warning. IPMI_OS_Critical_Stop_State The following states correspond to OS Critical Stop sensors that report an assertion or deassertion. IPMI_OS_Critical_Stop_State_No_Event Defaults to Nominal. IPMI_OS_Critical_Stop_State_Deasserted Defaults to Nominal. IPMI_OS_Critical_Stop_State_Asserted Defaults to Critical. IPMI_Slot_Connector The following states correspond to Slot Connector sensors w/ Slot Connector specific output states. IPMI_Slot_Connector_No_Event Defaults to Nominal. IPMI_Slot_Connector_Fault_Status_Asserted Defaults to Critical. IPMI_Slot_Connector_Identify_Status_Asserted Defaults to Warning. IPMI_Slot_Connector_Slot_Connector_Device_Installed_Attached Defaults to Nominal. IPMI_Slot_Connector_Slot_Connector_Ready_For_Device_Installation Defaults to Nominal. IPMI_Slot_Connector_Slot_Connector_Ready_For_Device_Removal Defaults to Nominal. IPMI_Slot_Connector_Slot_Power_Is_Off Defaults to Nominal. IPMI_Slot_Connector_Slot_Connector_Device_Removal_Request Defaults to Warning. IPMI_Slot_Connector_Interlock_Asserted Defaults to Warning. IPMI_Slot_Connector_Slot_Is_Disabled Defaults to Warning. IPMI_Slot_Connector_Slot_Holds_Spare_Device Defaults to Nominal. IPMI_Slot_Connector_Transition_Severity The following states correspond to Slot Connector sensors that report on device severity. IPMI_Slot_Connector_Transition_Severity_No_Event Defaults to Nominal. IPMI_Slot_Connector_Transition_Severity_Transition_To_OK Defaults to Nominal. IPMI_Slot_Connector_Transition_Severity_Transition_To_Non_Critical_From_OK Defaults to Warning. IPMI_Slot_Connector_Transition_Severity_Transition_To_Critical_From_Less_Severe Defaults to Critical. IPMI_Slot_Connector_Transition_Severity_Transition_To_Non_Recoverable_From_Less_Severe Defaults to Critical. IPMI_Slot_Connector_Transition_Severity_Transition_To_Non_Critical_From_More_Severe Defaults to Warning. IPMI_Slot_Connector_Transition_Severity_Transition_To_Critical_From_Non_Recoverable Defaults to Critical. IPMI_Slot_Connector_Transition_Severity_Transition_To_Non_Recoverable Defaults to Critical. IPMI_Slot_Connector_Transition_Severity_Monitor Defaults to Warning. IPMI_Slot_Connector_Transition_Severity_Informational Defaults to Nominal. IPMI_System_ACPI_Power_State IPMI_System_ACPI_Power_State_No_Event Defaults to Nominal. IPMI_System_ACPI_Power_State_S0_G0 Defaults to Nominal. IPMI_System_ACPI_Power_State_S1 Defaults to Nominal. IPMI_System_ACPI_Power_State_S2 Defaults to Nominal. IPMI_System_ACPI_Power_State_S3 Defaults to Nominal. IPMI_System_ACPI_Power_State_S4 Defaults to Nominal. IPMI_System_ACPI_Power_State_S5_G2 Defaults to Nominal. IPMI_System_ACPI_Power_State_S4_S5_Soft_Off Defaults to Nominal. IPMI_System_ACPI_Power_State_G3_Mechanical_Off Defaults to Nominal. IPMI_System_ACPI_Power_State_Sleeping_in_an_S1_S2_or_S3_States Defaults to Nominal. IPMI_System_ACPI_Power_State_G1_Sleeping Defaults to Nominal. IPMI_System_ACPI_Power_State_S5_Entered_By_Override Defaults to Nominal. IPMI_System_ACPI_Power_State_Legacy_ON_State Defaults to Nominal. IPMI_System_ACPI_Power_State_Legacy_OFF_State Defaults to Nominal. IPMI_System_ACPI_Power_State_Unspecified Defaults to Critical. IPMI_System_ACPI_Power_State_Unknown Defaults to Critical. IPMI_Watchdog2 The following states correspond to Watchdog 2 sensors w/ Watchdog 2 specific output states. IPMI_Watchdog2_No_Event Defaults to Nominal. IPMI_Watchdog2_Timer_Expired Defaults to Warning. IPMI_Watchdog2_Hard_Reset Defaults to Critical. IPMI_Watchdog2_Power_Down Defaults to Critical. IPMI_Watchdog2_Power_Cycle Defaults to Critical. IPMI_Watchdog2_Reserved1 Defaults to Nominal. IPMI_Watchdog2_Reserved2 Defaults to Nominal. IPMI_Watchdog2_Reserved3 Defaults to Nominal. IPMI_Watchdog2_Reserved4 Defaults to Nominal. IPMI_Watchdog2_Timer_Interrupt Defaults to Warning. IPMI_Platform_Alert_State The following states correspond to Platform Alert sensors that report an assertion or deassertion. IPMI_Platform_Alert_State_No_Event Defaults to Nominal. IPMI_Platform_Alert_State_Deasserted Defaults to Nominal. IPMI_Platform_Alert_State_Asserted Defaults to Critical. IPMI_Entity_Presence The following states correspond to Entity Presence sensors w/ Entity Presence specific output states. IPMI_Entity_Presence_No_Event Defaults to Nominal. IPMI_Entity_Presence_Entity_Present Defaults to Nominal. IPMI_Entity_Presence_Entity_Absent Defaults to Critical. IPMI_Entity_Presence_Entity_Disabled Defaults to Critical. IPMI_Entity_Presence_Device_Present The following states correspond to Entity Presence sensors that report on device installation. IPMI_Entity_Presence_Device_Present_No_Event Defaults to Nominal. IPMI_Entity_Presence_Device_Present_Device_Removed_Device_Absent Defaults to Nominal. IPMI_Entity_Presence_Device_Present_Device_Inserted_Device_Present Defaults to Nominal. IPMI_Management_Subsystem_Health The following states correspond to Management Subsystem Health sensors w/ Management Subsystem Health specific output states. IPMI_Management_Subsystem_Health_No_Event Defaults to Nominal. IPMI_Management_Subsystem_Health_Sensor_Access_Degraded_Or_Unavailable Defaults to Critical. IPMI_Management_Subsystem_Health_Controller_Access_Degraded_Or_Unavailable Defaults to Critical. IPMI_Management_Subsystem_Health_Management_Controller_Off_Line Defaults to Critical. IPMI_Management_Subsystem_Health_Management_Controller_Unavailable Defaults to Critical. IPMI_Management_Subsystem_Health_Sensor_Failure Defaults to Critical. IPMI_Management_Subsystem_Health_FRU_Failure Defaults to Critical. IPMI_Battery The following states correspond to Battery sensors w/ Battery specific output states. IPMI_Battery_No_Event Defaults to Nominal. IPMI_Battery_Battery_Low Defaults to Warning. IPMI_Battery_Battery_Failed Defaults to Critical. IPMI_Battery_Battery_Presence_Detected Defaults to Nominal. IPMI_Session_Audit The following states correspond to Session Audit sensors w/ Session_Audit specific output states. IPMI_Version_Change_No_Event Defaults to Nominal. IPMI_Version_Change_Hardware_Change_Detected_With_Associated_Entity Defaults to Warning. IPMI_Version_Change_Firmware_Or_Software_Change_Detected_With_Associated_Entity Defaults to Warning. IPMI_Version_Change_Hardware_Incompatability_Detected_With_Associated_Entity Defaults to Critical. IPMI_Version_Change_Firmware_Or_Software_Incompatability_Detected_With_Associated_Entity Defaults to Critical. IPMI_Version_Change_Entity_Is_Of_An_Invalid_Or_Unsupported_Hardware_Version Defaults to Critical. IPMI_Version_Change_Entity_Contains_An_Invalid_Or_Unsupported_Firmware_Or_Software_Version Defaults to Critical. IPMI_Version_Change_Hardware_Change_Detected_With_Associated_Entity_Was_Successful Defaults to Nominal. IPMI_Version_Change_Software_Or_FW_Change_Detected_With_Associated_Entity_Was_Successful Defaults to Nominal. IPMI_FRU_State The following states correspond to FRU State sensors w/ FRU State specific output states. IPMI_FRU_State_No_Event Defaults to Nominal. IPMI_FRU_State_FRU_Not_Installed Defaults to Critical. IPMI_FRU_State_FRU_Inactive Defaults to Critical. IPMI_FRU_State_FRU_Activation_Requested Defaults to Warning. IPMI_FRU_State_FRU_Activation_In_Progress Defaults to Warning. IPMI_FRU_State_FRU_Active Defaults to Nominal. IPMI_FRU_State_FRU_Deactivation_Requested Defaults to Warning. IPMI_FRU_State_FRU_Deactivation_In_Progress Defaults to Warning. IPMI_FRU_State_FRU_Communication_Lost Defaults to Critical. IPMI_OEM The following configuration options can be used to configure OEM specific interpretations. Users should be aware that both IPMI_OEM_Bitmask and IPMI_OEM_Value can be configured for an identical Manufacturer−ID, Product−ID, Event−Reading−Type−Code, and Sensor−Type combination. All interpretations rules for a specific combination are iterated through and the worst resulting sensor state is returned (i.e. Warning < Nominal, Critical < Warning). If no match is found, no sensor state is returned for the OEM sensor reading. For each of the configuration options below, <Manufacturer−ID> is the numeric IANA manufacturer ID for the manufacturer in question. The <Product−ID> is one or more numeric IDs representing the manufacturer's product. The <Product−ID> can be listed as a single numeric number (e.g. 1234), a range of IDs separated by a dash (e.g. 12-20), or a list of specific product IDs separted by a plus (e.g. 12+19+22). Both the Manufacturer−ID and Product−ID can be found using bmc-info(8). Multiple <Manufacturer−ID> and <Product−ID> pairs can be input separated by commas. The Event−Reading−Type−Code and Sensor−Type need not be OEM types. They may be non-OEM types and used to provide interpretation rules for sensors that may be behaving outside the standard of the IPMI specification. IPMI_OEM_Bitmask <Manufacturer−ID>:<Product−ID>,... Event−Reading−Type−Code Sensor−Type Sensor−Event−Bitmask State IPMI_OEM_Bitmask can be used to configure a state interpretation for a specific Manufacturer−ID, Product−ID, Event−Reading−Type−Code, and Sensor−Type combination and a specific bitmask of the Sensor-Event. The state will be accepted as the sensor interpretation if the inputted bitmask ANDed with the actual sensor event bitmask reading is true. As a special case, the state will be accepted if the inputted bitmask and the actual sensor event bitmask are both 0. In other words, if no events happened, an OEM interpretation can be configured for this case by inputing a bitmask of 0x0000. IPMI_OEM_Value <Manufacturer−ID>:<Product−ID>,... Event−Reading−Type−Code Sensor−Type Sensor−Event−Bitmask-Value State IPMI_OEM_Value can be used to configure a state interpretation for a specific Manufacturer−ID, Product−ID, Event−Reading−Type−Code, and Sensor−Type combination and a specific value for the Sensor−Event−Bitmask. The state will be accepted as the sensor interpretation if the inputted bitmask value is equal to the actual sensor event bitmask reading.

FILES/etc//freeipmi_interpret_sensor.conf

REPORTING BUGSReport bugs to <freeipmi−users@gnu.org> or <freeipmi−devel@gnu.org>.

COPYRIGHTCopyright (C) 2007-2012 Lawrence Livermore National Security, LLC. This library is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 3 of the License, or (at your option) any later version.

SEE ALSOlibfreeipmi(3), libipmimonitoring(3), ipmi-sensors(8) http://www.gnu.org/software/freeipmi/ 0

Johanes Gumabo

Data Size : 210,224 byte
man-ipmimonitoring.conf.5Build : 2024-12-05, 20:55 :
Visitor Screen : x
Visitor Counter ( page / site ) : 2 / 237,990
Visitor ID : :
Visitor IP : 3.14.131.115 :
Visitor Provider : AMAZON-02 :
Provider Position ( lat x lon ) : 39.962500 x -83.006100 : x
Provider Accuracy Radius ( km ) : 1000 :
Provider City : Columbus :
Provider Province : Ohio , : ,
Provider Country : United States :
Provider Continent : North America :
Visitor Recorder : Version :
Visitor Recorder : Library :
Online Linux Manual Page : Version : Online Linux Manual Page - Fedora.40 - march=x86-64 - mtune=generic - 24.12.05
Online Linux Manual Page : Library : lib_c - 24.10.03 - march=x86-64 - mtune=generic - Fedora.40
Online Linux Manual Page : Library : lib_m - 24.10.03 - march=x86-64 - mtune=generic - Fedora.40
Data Base : Version : Online Linux Manual Page Database - 24.04.13 - march=x86-64 - mtune=generic - fedora-38
Data Base : Library : lib_c - 23.02.07 - march=x86-64 - mtune=generic - fedora.36

Very long time ago, I have the best tutor, Wenzel Svojanovsky . If someone knows the email address of Wenzel Svojanovsky , please send an email to johanes_gumabo@yahoo.co.id .

If error, please print screen and send to johanes_gumabo@yahoo.co.id
Under development. Support me via PayPal.

ERROR : Need New Coding : (rof_escape_sequence|91|freeipmi_interpret_sensor.conf.5|68|\"). |lines can be continued on the next using backslash ("\\"). )