RPI-EEPROM-UPDATE - Online Linux Manual PageSection : 1
Updated : September 2021
Source : rpi-eeprom-update 12.12
Note : User Commands
NAMErpi-eeprom-update − Checks whether the Raspberry Pi bootloader EEPROM is up-to-date and updates the EEPROM
DESCRIPTIONrpi−eeprom−update [options]... [FILE] Bootloader EEPROM update tool for the Raspberry Pi 4. Checks whether the Raspberry Pi 4 bootloader and the VL805 USB controller EEPROMs are up to date and optionally updates the EEPROMs at the next reboot. The default update mechanism writes recovery.bin and the EEPROM update image(s) (pieeprom.upd and vl805.bin) to the boot partition. The SHA256 hash of the corresponding images are written to pieeprom.sig and/or vl805.sig. This guards against file system corruption which could cause the EEPROM to be flashed with an invalid image. This is not a security check. At the next reboot the ROM runs recovery.bin which updates EEPROM(s). If the update was successful recovery.bin renames itself to recovery.000 to prevent it from running a second time then resets the system. The system should then boot normally. If /boot does not correspond to the boot partition and this is not a NOOBS system, then the mount point for BOOTFS should be defined in /etc/default/rpi−eeprom−update by defining the BOOTFS variable. A backup of the current EEPROM config file is written to /var/lib/raspberrypi/bootloader/backup before applying the update. Unless the −d flag is specified, the current bootloader configuration is retained.
OPTIONS−a Automatically install bootloader and USB (VLI) EEPROM updates. −A Specify which type of EEPROM to automatically update (vl805 or bootloader) −b Outputs the path that pending EEPROM updates will be written to. −d Use the default bootloader config, or if a file is specified using the −f flag use the config in that file. This option only applies when a bootloader EEPROM update is needed; if the bootloader EEPROM is up to date then its config will not be changed. −f Install the given file instead of the latest applicable update Ignores the FREEZE_VERSION flag in bootloader and is intended for manual firmware updates. −h Display help text and exit −i Ignore package checksums − for rpi−eeprom developers. −j Write status information using JSON notation (requires −m option) −l Returns the full path to the latest available EEPROM image file according to the FIRMWARE_RELEASE_STATUS and FIRMWARE_IMAGE_DIR settings. −m Write status information to the given file when run without −a or −f −r Removes temporary EEPROM update files from the boot partition. This also cancels a pending update. −s Skips silent, automatic upgrades for default releases if the current bootloader release is newer than the version specified by BOOTLOADER_AUTO_UPDATE_MIN_VERSION 1599135103 −u Install the specified VL805 (USB EEPROM) image file.
ENVIRONMENTEnvironment variables should be defined in /etc/default/rpi−eeprom−update EEPROM_CONFIG_HOOK Specifies the path of an optional script which post−processes the configuration file before it is applied to the new image. The modified output must contain at least 3 lines and should contain WAKE_ON_GPIO and POWER_OFF_ON_HALT settings. FIRMWARE_RELEASE_STATUS Specifies the release status of the firmware to apply. Before selecting a firmware release directory this script checks whether there is a board revision specific variant e.g. default−c03111. If present then the board−revision specific version is used in preference. Release status: Bootloader releases follow a pipeline where images are released to the 'beta' directory first. The binaries are then promoted to 'latest' and finally 'default' so the 'default' binary is always the most tested release. default: The default bootloader image which supports all current models and hardware revisions. If a critical bug fix is required then the minimum default version number (BOOTLOADER_AUTO_UPDATE_MIN_VERSION) in the rpi−eeprom package is updated causing the bootloader to be automatically updated. latest: Contains the latest features which have undergone testing via the 'beta' release. Backwards compatiblity for configuration parameters is maintained once a feature is in the latest release directory. If the 'latest' release is selected then bootloader is automatically upgraded when the rpi−eeprom package is updated. As far as rpi−eeprom−update is concerned FIRMWARE_RELEASE_STATUS is just the subdirectory mapping under /home/shift/dev/rpi−eeprom/firmware. Therefore, custom release directories are supported by creating the relevant directory and changing the FIRMWARE_RELEASE_STATUS environment variable. The 'default' and 'latest' release names are symlinks to the old directory names of 'critical' / 'stable'.
EXAMPLES
rpi−eeprom−config pieeprom.bin −−out bootconf.txt
To update the configuration file in an EEPROM image:rpi−eeprom−config pieeprom.bin −−config bootconf.txt −−out pieeprom−new.bin
To flash the new image:sudo rpi−eeprom−update −d −f ./pieeprom−new.bin The syntax is the same as config.txt See online documentation for the list of parameters. The official documentation for the Raspberry Pi bootloader EEPROM is available at https://www.raspberrypi.org/documentation/hardware/raspberrypi/booteeprom.md Compute Module 4 (CM4): CM4 is designed to support embedded applications where physical access to the CM4 may be limited. An invalid bootloader configuration or software bug could cause the system to fail to boot so automatic updates are disabled. We also recommend write−protecting the SPI EPPROM after flashing it using usbboot.
CM4 bootloader and EEPROM update instructions:https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711_bootloader_config.md
usbboot instructions for flashing CM4 EMMC and bootloader EEPROM:https://www.raspberrypi.org/documentation/hardware/computemodule/cm−emmc−flashing.md The CM4 ROM does not support running recovery.bin from the EMMC on CM4 so this service is disabled by default. SELF_UPDATE from USB or Network boot is supported but this must first be enabled by removing ENABLE_SELF_UPDATE=0 from the EEPROM config via usbboot. After enabling self−update set the CM4_ENABLE_RPI_EEPROM_UPDATE=1 environment variable or define it in /etc/default/rpi−eeprom−update. N.B. If there is a power failure during SELF_UPDATE the EEPROM write may fail and usbboot must be used to flash the bootloader EEPROM. SELF_UPDATE is not recommended for updating the bootloader on remote systems. 0
Johanes Gumabo
Data Size : 17,965 byte
man-rpi-eeprom-update.1Build : 2024-12-05, 20:55 :
Visitor Screen : x
Visitor Counter ( page / site ) : 3 / 232,567
Visitor ID : :
Visitor IP : 3.146.176.112 :
Visitor Provider : AMAZON-02 :
Provider Position ( lat x lon ) : 39.962500 x -83.006100 : x
Provider Accuracy Radius ( km ) : 1000 :
Provider City : Columbus :
Provider Province : Ohio , : ,
Provider Country : United States :
Provider Continent : North America :
Visitor Recorder : Version :
Visitor Recorder : Library :
Online Linux Manual Page : Version : Online Linux Manual Page - Fedora.40 - march=x86-64 - mtune=generic - 24.12.05
Online Linux Manual Page : Library : lib_c - 24.10.03 - march=x86-64 - mtune=generic - Fedora.40
Online Linux Manual Page : Library : lib_m - 24.10.03 - march=x86-64 - mtune=generic - Fedora.40
Data Base : Version : Online Linux Manual Page Database - 24.04.13 - march=x86-64 - mtune=generic - fedora-38
Data Base : Library : lib_c - 23.02.07 - march=x86-64 - mtune=generic - fedora.36
Very long time ago, I have the best tutor, Wenzel Svojanovsky . If someone knows the email address of Wenzel Svojanovsky , please send an email to johanes_gumabo@yahoo.co.id .
If error, please print screen and send to johanes_gumabo@yahoo.co.id
Under development. Support me via PayPal.