thermald - Online Linux Manual Page
Section : 8
Updated : 8 May 2013
NAMEthermald − start Linux thermal daemon
SYNOPSISthermald [ OPTIONS"]
DESCRIPTIONthermald is a Linux daemon used to prevent the overheating of platforms. This daemon monitors temperature and applies compensation using available cooling methods. By default, it monitors CPU temperature using available CPU digital temperature sensors and maintains CPU temperature under control, before HW takes aggressive correction action. Thermal daemon looks for thermal sensors and thermal cooling drivers in the Linux thermal sysfs (/sys/class/thermal) and builds a list of sensors and cooling drivers. Each of the thermal sensors can optionally be binded to a cooling driver by the in kernel drivers. In this case the Linux kernel thermal core can directly take actions based on the temperature trip points, for each sensor and associated cooling device. For example a trip temperature X in a sensor can be associates a cooling driver Y. So when the sensor temperature = X, the cooling driver "Y" is activated. Thermal daemon allows one to change this relationship or add new one via a thermal configuration file (thermal-conf.xml). This file is automatically created (thermal-conf.xml.auto) and used, if the platform has ACPI thermal relationship table. If not this needs to be manually configured. For manual configuration refer to the manual page of the thermal-conf.xml. In some newer platforms the auto creation of the config file is done by a companion tool "dptfxtract". This tool can be downloaded from "https://github.com/intel/dptfxtract". It is suggested as parts of the install process, run dptfxtract. There can be multiple configuration files. User can select a configuration file via -config-file option to override the default selection. The default selection picks one of the file in the following order: - /etc/thermald/thermal-conf.xml.auto - /var/run/thermald/thermal-conf.xml.auto - /etc/thermald/thermal-conf.xml (*Assuming configure prefix=/ is used during build.) There is another companion tool "ThermalMonitor", which presents a graphical front end. This allows the monitoring of sensors and changing of thermal trips to give the user more control. The source code of "ThermalMonitor" is a part of the thermald github source, in the tools folder.
OPTIONS−h, −−help Show help options. −−version Print thermald version and exit. −−no-daemon Don't become a daemon: Default is daemon mode. −−loglevel=info log severity: info level and up. −−loglevel=debug log severity: debug level and up: Max logging. −−poll-interval Poll interval in seconds: Poll for zone temperature changes. To disable polling, set to zero. Polling can only be disabled, if available temperature sensors can notify temperature change asynchronously. −−dbus-enable Enable Dbus. −−exclusive-control Act as exclusive thermal controller. This will use user-space governor for thermal sysfs and take over control. −−ignore-cpuid-check Ignore cpuid check for supported CPU models. −−config-file Specify thermal-conf.xml path and ignore default thermal-conf.xml. −−ignore-default-control Ignore default CPU temperature control. Strictly follow thermal-conf.xml or thermal-conf.xml.auto. −−workaround-enabled Enable special workarounds for RAPL MMIO power limit and TCC offset every 30 seconds. This helps to disable RAPL MMIO when not used and adjust TCC offset in certain Lenovo laptops. −−disable-active-power Disable active power management. This will not set active power limits using RAPL MMIO. This may result in constrained performance, if the system boots up with lower power limits. −−adaptive Use DPTF adaptive tables when present. This will ignore thermald config via xml files. −−test-mode Force use adaptive mode and exit if not supported, instead of restarting in non adaptive mode. This option is primarily for developers. −−systemd Assume that thermald is started by systemd. This will prevent running as daemon irrespective of --no-daemon option. −−ignore-critical-trip If the configuration defined a critical temperature point, which is too low, this option will avoid shutting down the system on reaching this temperature limit.
SEE ALSOthermal-conf.xml(5) 0
Johanes Gumabo
Data Size : 10,919 byte
man-thermald.8Build : 2025-03-22, 13:26 :
Visitor Screen : x
Visitor Counter ( page / site ) : 3 / 1,209,100
Visitor ID : :
Visitor IP : 18.190.219.146 :
Visitor Provider : AMAZON-02 :
Provider Position ( lat x lon ) : 39.962500 x -83.006100 : x
Provider Accuracy Radius ( km ) : 1000 :
Provider City : Columbus :
Provider Province : Ohio , : ,
Provider Country : United States :
Provider Continent : North America :
Visitor Recorder : Version :
Visitor Recorder : Library :
Online Linux Manual Page : Version : Online Linux Manual Page - Fedora.40 - march=x86-64 - mtune=generic - 25.03.22
Online Linux Manual Page : Library : lib_c - 24.10.03 - march=x86-64 - mtune=generic - Fedora.40
Online Linux Manual Page : Library : lib_m - 24.10.03 - march=x86-64 - mtune=generic - Fedora.40
Data Base : Version : Online Linux Manual Page Database - 24.04.13 - march=x86-64 - mtune=generic - fedora-38
Data Base : Library : lib_c - 23.02.07 - march=x86-64 - mtune=generic - fedora.36
If error, please print screen and send to johanes_gumabo@yahoo.co.id
Under development. Support me via PayPal.
